Slant_fin VSL-160C Part C Bedienungsanleitung

7313.10.6 – Outdoor reset with room compensationWhile in the “Installers’ Menu” (section 13.17) set the parameter to 02. The system will function ex

8213 - USEE1413.18.2 - Diagnostics: “E” blocking errors (continued)“E” CodeBlocking descriptionChecks to makeSolutionsU8 return temperature sensor sho

83Service and maintenance schedulesService Technician User maintenanceAnnual Startup:- Address reported problems (Follow section 14.1.1);- Check all p

8414.1.6 - Check ignition and fl ame sense electrodes1. Remove the fan-burner assembly unit (see section 14.3)2. Remove any deposits accumulated on the

85plumbing contractor or authorized inspection agency, to ensure that the product has not been affected by corrosive water conditions and to ensure th

8614 - MAINTENANCEFigure 14-1 Removing the casing 14.2 - Removing the casingIn order to remove the casing, follow the steps below while refering to Fi

87Figure 14-2 Remove the fan-burner assembly unit14 - MAINTENANCE6. prepare a suitable cover for the gas valve outlet under nut “D” so that no dirt, w

88A = Left ignition electrodeB = Right ignition electrodeC = Flame detection electrodeFigure 14-3 Positioning electrodes on burner (Use a hand caliper

8914 - MAINTENANCE14.6 - Condensate trap cleaningThe condensate trap must be checked every year and cleaned if required. Follow the steps below to pro

9014 - MAINTENANCE14.7 - Circulator pump motor replacement (only for 160-C model)To replace the circulator pump follow the steps below while, refering

9114 - MAINTENANCE14.9 - 3-way valve removal (only for 160-C model)The 3-way valve, details “M” and “Q” in Figures 14-6 and 14-7, directs hot water pr

7413.12 - Delays, alarms and protective actionsTo protect the life of the appliance, improve comfort, and maximize energy savings, the following timin

9214 - MAINTENANCE14.10 - Draining the heating side of the boilerTo drain the heating side of the boiler follow the steps below: 1. cool boiler turnin

9314.13 - Water and fl ue temperature sensorThe boiler has a number of sensors that measure temperature. The electrical resistance between the sensor w

9414.15 - Functional wiring diagramWARNING!!!Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dang

9514 - MAINTENANCE

9614.16 - Multiwire wiring diagramWARNING!!! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dang

9714 - MAINTENANCE

98MODEL VSL-160-B; VSL-160-C;Country of destination USA and CanadaType of boiler Direct Vent and room

9916 - SPARE PARTS

10016 - SPARE PARTS

10116 - SPARE PARTS

7513.16 - “Users’ menu”When entering the “Users’ menu”, the display, item “1” in Figure 13-1, will start blinking indicating that a change of mode has

10216 - SPARE PARTSSpare parts list1 - 81 9010 000 - CABLE UL IGNITOR CONN 90° L1552 - 81 9011 000 - NUT ZINC COATED 6MA3 - 81 9012 000 - SILICONE PIP

10338 - 81 9047 000 - 3/8G MALE to 1/8NPT FEMALE BUSHING39 - 81 9048 000 - GASKET EPDM D38 F20 SP640 - 81 9049 000 - 45xx WALL MOUNTING BRACKET41 - 81

10417 - READ OUT FLOW CHARTPush and hold the RESET key for a time, in seconds, indicated by the numberPush and release the RESET keyPush and hold toge

10517 - READ OUT FLOW CHARTCentral heatingAnti Freeze protectionLock-outBlocking errorD.H.W. active more than 120 min. Anti legionella protectionLast

106 may assume the follow values:61 - for boilers at NATURAL gas;62 - for boilers at LP gas; may assume the follow values:00 - 230Vac, 50Hz, °C;01 - 2

107NOTE62403559 R00 May 03, 2012

SLANT/FIN CORPORATION, Greenvale, N.Y. 11548 • Phone: (516) 484-2600FAX: (516) 484-5921 • Canada: Slant/Fin LTD/LTEE, Mississauga, Ontariowww.slantfin

7613 - USE13.17 - “Installer’s menu”CAUTION!!! Changing these parameters could cause the boiler and therefore the system to malfunction. For this rea

7713 - USEPARAMETER DESCRIPTION INFORMATION ON DISPLAY ITEM “2” OF FIGURE 13-1Can be changed (see Section 13.9): 00 = thermostatic adjus

7813.18 - DiagnosticsDuring the normal operation of the boiler, the display, of Figure 13-1, continually shows the operating status of the boiler as s

7913.18.1 - Diagnostics: “L” lock-outs“L”CodeLock-out descriptionChecks to makeSolutionsL01L02L03L0413 - USEL05L06L07L08L09L10L12L13L14L15L16No fl ame

8013 - USE“L” CodeLock-out descriptionControlsSolutionsL18L19L20L25L32L33L45L46Program errorFlame sensed for 10 seconds, after the closure of the gas

8113 - USE13.18.2 - Diagnostics: “E” blocking errors“E” CodeBlocking descriptionChecks to makeSolutionsE01E02E04E07E08E11E12E13U1 boiler temperature s